Nokia Plumbing Product CVT GCU SX User Manual

Installation Guide for  
GigaBit TX to SX Tap  
Model CVT-GCU/SX  
Doc. PUBCVTGCUSXU Revised 03/07  
 
 
Installation Guide for Gigabit TX/SX Tap  
Table of Contents  
Introduction.                                                                                                          1  
Key.Features.                                                                                                        1  
Product.Diagram.                                                                                                  2  
Connecting.a.GigaBit.TX.to.SX.Tap.to.the.Network.                                          3  
Connecting.a.GigaBit.TX.to.SX.Tap.to.the.Monitoring.Device.                          5  
Specifications.                                                                                                      7  
Warranty.                                                                                                              8  
 
Installation Guide for Gigabit TX/SX Tap  
PLEASE READ THESE LEGAL NOTICES CAREFULLY.  
By.using.a.Net.Optics.Tap.you.agree.to.the.terms.and.conditions.of.usage.set.forth.by.Net.Optics,.Inc  
No.licenses,.express.or.implied,.are.granted.with.respect.to.any.of.the.technology.described.in.this.  
manual .Net.Optics.retains.all.intellectual.property.rights.associated.with.the.technology.described.in.  
this.manual .This.manual.is.intended.to.assist.with.installing.Net.Optics.products.into.your.network  
Trademarks and Copyrights  
©.2007.by.Net.Optics,.Inc .Net.Optics®.is.a.registered.trademark.of.Net.Optics,.Inc .Additional.com-  
pany.and.product.names.may.be.trademarks.or.registered.trademarks.of.the.individual.companies.and.  
are.respectfully.acknowledged  
Additional Information  
Net Optics, Inc. reserves the right to make changes in specifications and other information contained  
in.this.document.without.prior.notice .Every.effort.has.been.made.to.ensure.that.the.information.in.this.  
document.is.accurate .Net.Optics.is.not.responsible.for.typographical.errors  
 
Installation Guide for Gigabit TX/SX Tap  
Introduction  
Net Optics GigaBit TX to SX Tap simplifies connecting FX fiber monitoring  
and.security.devices.to.GigaBit.copper.network.links .Convert.TX.to.SX.and.  
tap.into.the.link.with.one.device,.reducing.cost.and.complexity.at.the.same.  
time .GigaBit.TX.to.SX.Taps.support.passive.monitoring.of.GigaBit.links.at.  
speeds.at.1000.Mbps  
Transparent Access  
GigaBit.TX.to.SX.Taps.establish.permanent.passive.access.ports.without.  
introducing.a.point.of.failure.or.disturbing.other.network.connections .These.  
passive.Taps.deliver.full-duplex.monitoring.with.zero.impact.on.network.traf-  
fic around the clock.  
Security and Visibility  
Without.an.IP.address,.monitoring.devices.are.isolated.from.the.network,.  
dramatically.reducing.their.exposure.to.attacks .However,.the.monitoring.  
device connected to the Tap still sees all full-duplex traffic as if it were in-line,  
including.Layer.1.and.Layer.2.errors  
Simply Plug It In  
Full-duplex.monitoring.is.a.snap.with.supplied.cables .All.networking.and.  
monitoring.cables.necessary.for.plug.and.play.deployment.are.included.with.  
the.Tap  
Reliability  
For.extra.uptime.protection,.Net.Optics.GigaBit.TX.to.SX.Taps.offer...  
redundant.power.connections .Should.the.primary.power.source.fail,.the.Tap.  
automatically.switches.to.the.backup.power.source .Power.LEDs.on.the.front.  
of.the.Tap.indicate.the.current.power.source.–.even.if.power.is.lost.and.reap-  
plied, there is always zero delay to network traffic.  
Key Features  
Passive, Secure Technology  
•. Provides.passive.access.at.speeds.at.1000.Mbps.without.data.stream.  
. interference.or.introducing.a.point.of.failure  
• Access GigaBit copper links with SX fiber devices without a separate  
converter  
•. Permanent.in-line.installation.without.affecting.network.performance  
 
Installation Guide for Gigabit TX/SX Tap  
Key Features (continued)  
Passive, Secure Technology  
• Passes all full-duplex traffic (including errors) from all layers for  
comprehensive.troubleshooting  
•. No.IP.address.is.needed.for.the.Tap.or.monitoring.device,.enhancing..  
monitoring.security  
•. Redundant.power.ensures.monitoring.uptime  
•. Fully.IEEE.802 3.compliant  
Ease of Use  
•. LED.indicators.show.redundant.power.and.link.status  
•. Front-mounted.connectors.make.installation.and.operation.quick.and.easy  
•. Silk-screened.application.diagram.illustrates.all.connections.for.easy..  
deployment  
•. Optional.19-inch.rack.frames.hold.up.to.3.or.12.Taps  
•. Tested.and.compatible.with.all.major.manufacturers’.monitoring.devices,.  
including.protocol.analyzers,.probes,.and.intrusion.detection/prevention.  
systems  
Support  
•. Net.Optics.offers.free.technical.support.throughout.the.lifetime.of.your.  
purchase. Our technical support team is available from 8 am to 5 pm Pacific  
Time, Monday through Friday at +1 (408) 737-7777 and via email at  
ts-support@netoptics com .FAQs.are.also.available.on.Net.Optics.website.  
at.www netoptics com  
Product Diagram  
Network  
GigaBit TX to SX Converter Tap  
A
B
A
B
2
1
®
LASER  
CAUTION!  
LINK ACT  
LINK ACT  
Monitor  
Monitor A/B  
SX  
Network B  
TX  
LED  
Indicators  
Network A  
TX  
Figure.1  
 
Installation Guide for Gigabit TX/SX Tap  
Connecting a GigaBit TX to SX Tap to the Network  
.
1 .Unpack.the.Tap.and.verify.that.you.have.all.components,.and.obtain.the.  
required.cables.needed.to.successfully.install.the.unit  
2 .Connect.Network.Port.A.to.the.appropriate.switch,.server.or.router.using.a.  
CAT5E RJ45 straight-thru cable. This will act as your DCE interface.  
3 .Connect.Network.Port.B.to.the.appropriate.switch,.server.or.router.using.a.  
CAT5E RJ45 straight-thru cable. This will act as your DTE interface.  
4. Verify that the Tap Network Ports are cabled in-line between two devices.  
Link Fault Signaling  
. The.Tap.negotiates.separately.with.each.side.of.the.full-duplex.link,..  
detecting.if.either.side.fails .In.the.event.of.a.failure,.the.Tap.ceases.nego-  
tiation.with.the.remaining.side,.enabling.a.clean.fail-over.to.a.redundant.  
network connection (if one is available).  
A
B
Network  
GigaBit Converter Tap  
Monitor  
®
A
B
2
1
LASER  
CAUTION!  
ACT LINK  
ALINK  
To network switch or router  
To network switch or router  
Figure.2  
3
 
Installation Guide for Gigabit TX/SX Tap  
Connecting a GigaBit TX to SX Tap to the Monitoring  
Device  
1 .Supply.power.to.the.Tap.using.the.2.redundant.power.supplies.included.  
with the unit. Verify that the Power LED illuminates.  
2 .Using.a.Net.Optics.Custom.Monitor.Cable,.connect.the.single-duplex.end.  
to.the.Tap.Monitor.Port.A/B  
3 .Connect.the.twin-duplex.end.of.the.cable.labeled.DCE.into.the.appropriate.  
monitoring.device.port.to.monitor.the.DCE.link .  
4. Connect the other twin-duplex end to the appropriate monitoring device  
port.to.monitor.the.DTE.link .  
5 .Compare.the.LEDs.on.the.Tap.to.the.chart.below.to.verify.correct.setup:.  
PWR1: Power 1. This LED illuminates (Green) when device is powered  
up  
PWR2: Power 2. This LED illuminates (Green) when redundancy is .  
powered.up  
LK: Link. This LED illuminates (Green) when link is established with  
another.device.  
Tx: Transmit. This LED illuminates (Green) when UTP port is transmitting  
a.signal .  
Rx: Receive. This LED illuminates (Green) when UTP port is receiving a  
signal .  
Additional GigaBit TX/SX Tap LEDs are located in the upper left and  
right hand corners of the RJ45 connectors for Port A and Port B  
•. Link Indicator: Located.in.the.upper.right.hand.corner .If.a.good.link.is.  
established,.the.LED.illuminates.a.steady.green .If.there.is.current.activity.  
on this link, the LED flashes.  
Note: The SC connectors on the Custom Analyzer Cable contain  
RX connections only.  
 
Installation Guide for Gigabit TX/SX Tap  
Connecting a GigaBit TX to SX Tap to the Monitoring  
Device  
A
B
Network  
GigaBit Converter Tap  
Monitor  
®
A
B
2
1
LASER  
CAUTION!  
ACT LINK  
ACT LINK  
To monitoring device  
Figure.3  
 
Installation Guide for Gigabit TX/SX Tap  
Specifications  
Splitter Specifications:  
Split.Ratio:.50/50  
Fiber.Type:.Multimode.Corning.62 5/125µm,.wavelength.850nm  
Insertion Loss: Network Port: ≤ 4.5 dB  
Monitor Port: ≤ 4.5 dB  
Operating Specifications:  
Operating Temperature: 10˚C to 55˚C  
Storage Temperature: 0˚C to 70˚C  
Relative.Humidity:.10%.min,.95%.max,.non-condensing  
Mechanical Specifications:  
Power Supply: Input: 100-240 VAC, 47-63 Hz, 0.5A  
(AC100-125V, 50-60Hz, 30VA for Japan)  
Output: 12V, 1.5A (5V, 2.4A for UK and Japan)  
Dimensions: 1.125" high x 6.5" deep x 4.5” wide  
Connectors:  
(1) Duplex SC connector (monitoring port)  
(2) RJ45, 8 pin connectors (network ports)  
Cable Interface:  
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5E  
Fiber Optic Interface:  
Laser:.Class.I,.eye-safe,.laser.emitter.type .These.Class.I.Lasers.conform.  
to the applicable requirements per US 21 CFR (J) and EN 60825-1, also  
UL.1950.applications  
Optical.Transmitter.Wave.Length:.850.nm.nominal.  
Output Power: -9.5 dB min, -4.0 dB max  
Optical.Receiver.Input.Sensitivity:..0.dB.min,.-17.dB.max  
 
Installation Guide for Gigabit TX/SX Tap  
Limitations on Warranty and Liability  
Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC.  
BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUD-  
ING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY  
DEFECT.OR.INACCURACY.IN.THIS.MANUAL.ITSELF .THIS.INCLUDES.BUT.IS.NOT.LIM-  
ITED TO LOST PROFITS, LOST SAVINGS, AND ANY INCIDENTAL OR CONSEQUENTIAL  
DAMAGES.ARISING.FROM.THE.USE.OR.INABILITY.TO.USE.THIS.PRODUCT,.even.if.Net.  
Optics.has.been.advised.of.the.possibility.of.such.damages .Some.states.do.not.allow.the.exclusion.  
or.limitation.of.implied.warranties.or.liability.for.incidental.or.consequential.damages,.so.the.above.  
limitation.or.exclusion.may.not.apply.to.you  
Net.Optics,.Inc .warrants.this.Tap.to.be.in.good.working.order.for.a.period.of.ONE.YEAR.from.the.  
date.of.purchase.from.Net.Optics.or.an.authorized.Net.Optics.reseller  
Should.the.unit.fail.anytime.during.the.said.ONE.YEAR.period,.Net.Optics.will,.at.its.discretion,.  
repair.or.replace.the.product .This.warranty.is.limited.to.defects.in.workmanship.and.materials.and.  
does not cover damage from accident, disaster, misuse, abuse or unauthorized modifications.  
If.you.have.a.problem.and.require.service,.please.call.the.number.listed.at.the.end.of.this.section.and.  
speak.with.our.technical.service.personnel .They.may.provide.you.with.an.RMA.number,.which.must.  
accompany any returned product. Return the product in its original shipping container (or equivalent)  
insured.and.with.proof.of.purchase  
Additional Information  
Net Optics, Inc. reserves the right to make changes in specifications and other information contained  
in.this.document.without.prior.notice .Every.effort.has.been.made.to.ensure.that.the.information.in.  
this.document.is.accurate .Net.Optics.is.not.responsible.for.typographical.errors  
THE WARRANTYAND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF  
ALL.OTHERS,.EXPRESS.OR.IMPLIED .No.Net.Optics.reseller,.agent,.or.employee.is.authorized.  
to make any modification, extension, or addition to this warranty.  
Net.Optics.is.always.open.to.any.comments.or.suggestions.you.may.have.about.its.products.and/or.  
this.manual  
Send.correspondence.to.  
Net.Optics,.Inc .  
5303.Betsy.Ross.Drive.  
Santa Clara, CA 95054 USA.  
Telephone: +1 (408) 737-7777.  
Fax: +1 (408) 745-7719.  
Email:.info@netoptics com/Internet:.www netoptics com  
All.Rights.Reserved .Printed.in.the.U S A .No.part.of.this.publication.may.be.reproduced,.transmit-  
ted,.transcribed,.stored.in.a.retrieval.system,.or.translated.into.any.language.or.computer.language,.  
in.any.form,.by.any.means,.without.prior.written.consent.of.Net.Optics,.Inc ,.with.the.following.  
exceptions:.Any.person.is.authorized.to.store.documentation.on.a.single.computer.for.personal.use.  
only.and.that.the.documentation.contains.Net.Optics’.copyright.notice  
7
 
Installation Guide for Gigabit TX/SX Tap  
Notes:  
 
Installation Guide for Gigabit TX/SX Tap  
Notes:  
 
 
©.2007.by.Net.Optics,.Inc .All.Rights.Reserved ..  
 

Miele Washer Dryer W 2240 User Manual
Nady Systems Intercom System PMC 2X User Manual
NEC Server EXP320A User Manual
Nikon Network Card EH 6a User Manual
Numark Industries Musical Toy Instrument M2 User Manual
Oki Printer 4250n User Manual
Omnimount Indoor Furnishings 1004264 User Manual
One for All Universal Remote URC 4700 User Manual
Panasonic Cell Phone EB GD96 User Manual
Panasonic Projection Television PT 50LCZ70 User Manual