Step 10
Route your systems cables through Cable Ports and out through opening in rear
of Back Post.
Assembly Instructions
Stellar Video Table: G363
Thank you for purchasing an OmniMount product.
Specifications are subject to change without prior notice.
•
•
•
•
Three shelf video table
Every effort has been made to provide accurate and error-free assembly and installation. OmniMount
Systems disclaims liability for any difficulties arising from the interpretation of information contained
in these instructions. If OmniMount products are used for purposes other than their original intent,
OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property
damage, direct, indirect, or consequential, which may arise from the inability to use this product safely,
properly, and in the manner for which it has been designed and manufactured. Warranty does not
apply to products which have been lost, damaged by misuse, abuse, or accident.
Adjustable center shelf
Ideal for large LCD/DLP, Plasma TV’s
Cable management
IMPORTANT: Consult your dealer if you have any questions regarding
the proper assembly of this product.
OmniMount Systems, Inc.
8201 South 48th Street • Phoenix, AZ 85044-5355
8
P/N 1002697 Rev A 02/2005
Step 7
Step 1
Rock table to check that it is level and stable. For unstable condition, unscrew
shortest Leveling Foot until table sits level.
Refer to Fig. 1.
Install End Caps (M) into bottom of Main Frame (C) using rubber mallet.
Determine desired location of middle shelf; high or low. Install Center Support
Brackets (K) to desired
Peel Self Adhesive Pads (L) from backing paper, and apply to table assembly as
indicated by the black dots, as shown in Fig. 7.
shelf location with Hex
Note: There should be 5 Adhesive pads applied to each shelf.
Fig. 1
Screws (I), and Small Hex
Wrench (P).
Fig. 7
Step 2
Insert open end of Main Support Legs (E) and Center Support Legs (F) over brack-
ets on Main Frame, as shown in Fig. 2.
Note: The curve on the Support Legs should face inwards, and the mounting
holes should face towards the bottom of the Main Frame.
Loosely secure Support
Legs to Main Frame with
Hex Screws.
Fig. 2
Fig. 8
Step 8
Identify Glass Shelves by shape, as
shown in Fig. 8.
6
3
Step 3
Step 5
Fig. 5
Install Main and Center Support Legs over brackets on the other side of Main
Frame, as shown in Fig. 3. Loosely secure Support Legs to Main Frame with Hex
Screws.
Refer to Fig. 5.
Thread Hex Screws into bottom foot area of Back Post
(D). These will become the Leveling Feet for the com-
pleted table assembly.
Fig. 3
Snap Cable Port Covers (N) into cable openings
on Back Post.
Install End Caps (M) into top section of Back Post
using rubber mallet.
Step 6
Install Back Post onto rear of Support Legs using Long Hex Head Screws (H)
and Large Hex Wrench (O), as shown in Fig. 6.
Step 4
Tighten all Hex Screws on table assembly securely.
Attach Center Cross Bar (G) to Center Support Legs with Cross Bar Bracket (J) and Hex
Screws, as shown in Fig. 4.
Fig. 4
Fig. 6
4
5
|
Miele Ventilation Hood HS60CIW1 User Manual
MTD Chipper 640A thru 645A User Manual
Multiquip Automobile Parts MQ D306HA User Manual
Multi Tech Systems Network Router FR2201 User Manual
NAD Stereo Receiver 7140 User Manual
Nokia Cell Phone NOKIA 3100 User Manual
NordicTrack Home Gym NTEL75062 User Manual
Omega Stud Sensor FCLTX 100 User Manual
Onkyo Stereo System HT S3300 User Manual
P3 International Vacuum Cleaner P4900 User Manual