S.252
USER MANUAL
NOTE ON USE
• Allow for sufficient heat dispersion when installed on a rack.
• Handle the power cord carefully.
• Hold the plug when unplugging the cord.
• Keep the set free from moisture, water, and dust.
• Unplug the power cord when not using the set for long periods of time.
• Do not obstruct the ventilation holes. (For sets with ventilation holes.)
• Do not let foreign objects in the set.
• Do not let insecticides, benzene, and thinner come in contact with the set.
• Never disassemble or modify the set in any way.
FUNCTIONS
1) EJECT: Opens the CD door
12) LOOP: Press once to set starting loop point, press
again set ending point and enter loop. Press a third
time to exit loop.
2) STOP: Stops the CD.
3) SKIP: Skips through the tracks on the CD, forward or
13) LCD DISPLAY: Shows time (minutes, seconds,
back.
frame), and pitch information.
4)
: Scans forward or back through the
14) PITCH FADER: Used to speed up or slow down cur-
current track. This unit features 3 scan speeds. Keep
rent track.
the
to change the scan speed.
5) PLAY/PAUSE: Plays or pauses the CD. Autocue func-
or
button pressed for a few seconds
15) AUDIO OUT: This stereo line output connects to the
line input on any DJ mixer.
tion sets the cue point automatically when this button is 16) DIGITAL OUTPUT: This coaxial (S/P DIF) digital out-
used.
put connects to any RCA S/P DIF input, as found on
most standard computer sound cards or CD burners.
6) CUE: Used to recall and preview the cue point.
17) FADER START: Connects to any DJ mixer equipped
with a fader start input. This enables the user to start
the CD from the cue point, using the mixer’s cross or
line fader, depending on the mixer.
7) TIME: LCD display reads the time remaining or time
elapsed, according to this button.
8) PITCH: Turns pitch fader ON and OFF.
9) PITCH SELECT: Pressing the PITCH and PITCH
BEND - (minus) buttons simultaneously changes the
pitch fader range between +/- 8, 12, and 16%.
18) VOLTAGE SELECTOR: Used to select the unit’s volt-
age according to the local setting. Note: The voltage
should preset correctly from the factory, however,
make sure to check it before powering the unit.
*Just for Dual Voltage model only.
10) PITCH BEND: Maximum pitch on this unit is 16%. If
the pitch fader is already physically set to 16%, this
function will not work.
19) AC IN: This is the connection for the supplied power
: Switches between Single or Continuous
11) SGL/CTN
cable.
play modes.
20) POWER: This button is used to power the unit ON and
OFF.
21) PHONES: Use this stereo jack to connect a pair
of headphones.
2
FUNCTIONS
1
14
13
2
3
12
11
4
10
5
6 7 8
9
15
16 17
18
19
20
21
3
SPECIFICATION
POWER SOURCE
Dual Voltage:
AC 115/230V, 50/60Hz
Single Voltage:
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K.)
DIMENSIONS
WEIGHT
216(W) x 275(H) x 88(D) mm
2.3Kgs
4
WARRANTY & RETURN POLICY
Warranty
Through Stantons authorized dealers around the World, Stanton, or one of Stantons authorized distributors outside the U.S., will, without charge, repair
or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective
in material or workmanship for a period of one (1) year following the date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier of either thirty (30) days following the date of original
purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made necessary by reason of mi -
use, alteration, normal wear, or accident are not covered under this warranty.
Returns
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring warranty repair or replace-
ment must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from whom the merchandise was purchased and in the
same country where the merchandise was purchased. For purposes of purchases made via the Internet, the merchandise must be returned to the author-
ized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton
dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized dealer or to
an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and follow such authorized
Stanton dealers return policy.
Stanton assumes no risk and shall be subject to no liability for damage or loss resulting from the specific use or application made of the merchandise.
Stantons liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating
to the merchandise shall not exceed the price received by Stanton from our purchase of such merchandise. In no event will Stanton be liable for any
special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence
of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and
country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please include a written expla-
nation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Please register your product online at www.stantondj.com.
Stanton Magnetics
3000 SW 42nd Street
Hollywood FL 33312
Phone: +1 954.316.1500
Technical Support:
HYPERLINK "mailto:service@stantonmagnetics.com"
service@stantonmagnetics.com
LITS00008 REV-A
5
|